Redi-Roof is an architectural metal roofing system available exclusively from Petersen Aluminum Corporation. It may be specified in either a snap-on batten or standing seam profile and is intended for application over a solid substrate with a minimum 3:12 roof pitch. Typical underlayments include plywood, nailboard insulation or equal. Panels are to be factory roll-formed in continuous lengths (minimum panel length is 4 feet).
Redi-Roof Panels feature an offset profile which adds strength and allows room for a hex head fastener. The clip, with it's button punched design, insures an extra-snug fit. The one-piece design of the Redi-Roof Standing Seam allows for ease of installation.
UL 90 Rating
Steel Redi-Roof Panels carry a UL-90 rating for wind uplift when fastened to an underlayment assembly including 5/8" plywood or OSB (oriented strand board) laminated to rigid insulation (UL Construction No. 350 & 353)). For further details contact Petersen Aluminum Corporation.
Air and Water Infiltration
Petersen Redi-Roof Panels meet the full performance requirements of the ASTM E 283 air infiltration test and the ASTM E 331 water penetration test when applied over a solid substrate. For complete test results, Contact Petersen Aluminum Corporation.
Materials
a) 24 ga. G-90 hot dipped galvanized steel b) .032 3105-H14 aluminum or equal
Trim
All flashing and trim will be fabricated by manufacturer or qualified fabricator. Flashing shall be PAC-CLAD aluminum (.032-.080 gauge as specified) or PAC-CLAD steel (22 ga. or 24 ga. as specified). A 20 year warranty shall be supplied covering finish performance.
Installation
PAC-CLAD Redi-Roof shall be installed over solid decking with an underlayment of 30# (min.) roofing felt applied horizontally from eave to ridge. Panels shall be fastened using Petersen non-penetrating clips, fastening on 18" centers (max.). Minimum slope at 3:12 pitch. Consult a local architect/engineer for requirements of local codes and conditions.
| Product Features | |
| •Available
with or without offsets •Factory eave notching available •Herr-Voss corrective leveled •Labor-saving one-piece design •Stiffener beads available |
|
| Material | |
 |
•30
standard colors (steel) •20 standard colors (aluminum) •Smooth and stucco embossed available •20 year non-prorated finish warranty • Galvalume Plus available |
| UL-90 Rating | |
| •UL
90 Rating over solid substrate (steel only) •UL-790 Class A fire rated •UL-263 fire resistance rated •Wind load testing results available |
|
| ASTM Tests | |
| •ASTM
E283 tested •ASTM E331 tested |
|
 |
A complete ManuSpec¿ specification is available on request from Petersen Aluminum Corporation
|
Architect: Dennis Rainoshek Architects
General Contractor: Dillard & Weaver Construction, Inc.
Roofing Contractor: R. W. Honea Sheet Metal, Inc.
Color: Interstate Blue
Profile: Snap-Clad
*24 ga. panels listed in bold print are UL-90 rated over solid substrate.
Curved Batten Panel
The Redi-Roof Batten Panel is the industry's only batten panel which can be radiused concave or convex with a minimum radius of 9 ft. This panel is ideal for barrel vaults and cornices.
Calvert Pine Senior Center Prince Frederick, MD
Owner: Calvert County Board of Commissions
Architect: Collins & Kronstadt Architects
Roofing Contractor: J. E. Woods & Sons.
Color: Medium Bronze
Profile: Integral Batten
Pinehurst Resort & Country Club Centennial Course No. 8 Pinehurst, NC
Owner: Club Corporation of America
Architect: James R. McVicker Jr., AIA
Roofing Contractor: McRae Roofing Inc.
Color: Hemlock Green
Profile: Snap-Clad
